This is a spare part for MFG Crosswind rudder pedals.Compatible with MFG Crosswind V1 and V2 pedalsInstructions are below in attachment file !Keep in mind that YOU WILL NEED REPLACEMENT BRAKE AXIS CABLE, which you can also purchase in spare parts....but pay attention if you need V2 or V1 cables !!!!Compatible with V1,V2,V3 pedals
This is a spare part for MFG Crosswind rudder pedals.Compatible with MFG Crosswind V1 and V2 pedalsInstructions are below in attachment file !Keep in mind that YOU WILL NEED REPLACEMENT BRAKE AXIS CABLE, which you can also purchase in spare parts....but pay attention if you need V2 or V1 cables !!!!Compatible with V1,V2,V3 pedals
In case you want different revision from one shipped in your MFG Crosswind pedals.Rev.2 spring is approx 13% stronger (and slightly modified fit) than original Rev.1. spring fitted on earlier rudder pedals. (from 28.04.2020 we fit Rev.1 springs on new pedals again !Both revisions are compatible with V1,V2 and V3 pedalsTo determine which you already have...
Cables are preassembled with connectors and sensorsFor MFG Crosswind V2 & V3, as pinout on the cable differ from V1 !!!If you doubt what is your model of the pedals take a look at the picture. Some pedals have retrofitted newer electronics and therefore USB plug will clearly indicate which cable you need !IMPORTANT !!! - Yoinnovati A1302 sensor Read...
Za one koji su izgubili neki vijak ili oprugu. Kit sadrži standardnu oprugu, zakačni vijak s podesivom maticom i kapicu, imbus ključ, dva seta po 4x vijka (kraći i duži)Compatible with V1,V2 and V3 pedals
USB universal joystick controller boardFitted in MFG Crosswind rudder pedals since S/N 0337(V2&V3)Rudder pedals firmware is v5.xx (current v5.05)Universal joystick firmware is v7.xx ( current v7.16)Made in Croatia ( EU )Read description for full info
Sturdy, Ergonomic, antislip designs for flying in shoes or barefoot. - Kit consist of left + right footrest, 4x screws- Compatible with ALL MFG Crosswind models (V1,V2,V3) and WAP addon- Easy footrests style change on only 2x screws per footrestFor 3d printed pedals - Installation Allan imbus key (M6 screw) not included with MFG Crosswind - available as...
Alternativni profil za centriranje rudder osi na MFG Crosswind pedalamaBoja : grafit/crnaCompatible with V1,V2 and V3 pedals
Alternativni profil za centriranje rudder osi na MFG Crosswind pedalamaBoja : grafit/crnaCompatible with V1,V2 and V3 pedals
This is a spare part for MFG Crosswind rudder pedals. Consists of both LEFT + RIGHT sensor capCompatible with MFG Crosswind V1,V2,V3 pedals when paired with Yoinnovati sensor cable
This is a spare part for MFG Crosswind rudder pedals. If you exceed 100 kg force on brakes you will need it sooner or later :-)brake limiter set include both left and right limiterComposite material, M6 nut glued inCompatible with MFG Crosswind V1,V2 and V3 pedals, standard part for 20 degree brake action
This is a spare part for MFG Crosswind rudder pedals. Consists of both LEFT + RIGHT shaft NOTE For V1 pedals : it is likely that you will need small spacer of 0,5mm under sensor cap for a sensor to operate at full range of adjusted angles. spacer can be made of simple paper for example !Compatible with V1,V2 and V3 pedals
2020 by MFG. All Rights Reserved